Does It Matter Which Sata6g Port Is Used First
It will boot from the first disk it finds with a valid partition map and a partition marked as being bootable. And then it handed over its first-generation X25-Ms.
Does It Matter Which Sata Port You Use Pc Guide 101
For example the AKiTiO Thunder2 Quad and the AKiTiO Thunder3 Quad were created mainly for 35 drives and use only one PCIe lane per drive.
. Nope They should all run fine. Thats what I do on my computer at least. The manual sometimes says use port x for SSDOS but if it doesnt say that youre good with any of them.
On your board all the ports are the same so it doesnt matter other than drive order. Previously motherboards included old SATA versions and new the old types were slower and only really useful for stuff such as DVD drives which couldnt readwrite faster anyway. If the SATA ports are the same speeds it doesnt really matter.
Jan 15 2017 21 0. Every port does a 6gbs transfer rate which sucks but oh well. Refer to the images below to help you locate the Serial ATA SATA ports on your desktop board and determine if any of the SATA ports are affected by the Chipset Circuit Design Issue.
Aug 11 2006. Dont think Ive any m2 drives. Lets first say that when we started this we were absolutely sure wed see a difference.
The answer to that is that it depends on the amount of drives and if a RAID set is created with those drives or not. All of your ports will have the same speed. So you want your primary disk drive to be connected to port 0.
You would want any SSDs on the 6Gbs ports. And an m2 pcie drive in the second m2 disables the last pcie slot. It doesnt suck almost all HDDsSSDs fall within the 6GBs range yes I know the 950 Pro and 750 series and HyperX Predator so it would make sense that they use the most popular speed.
Id use SATA0 for the boot drive anything else doesnt matter. My motherboard model is H170-PRO as its manufacturer is ASUSTeK COMPUTER INC. Basically an m2 sata drive in the second m2 slot disables sata port 3.
In other words as long as you are not using cheap knock-off cables there should not be any difference. On some boards there are SATA 3Gbs ports and SATA 6Gbs ports. Without the manual Im not 100 sure but use 1.
Yes the Samsung and OCZ drives are able to present quantifiable gains. These days however all of the SATA. That can be changed in a BIOS setting.
However two SATA 6Gbps ports the pair of Marvell controllers. If some of them are faster 60 vs 3015 then you will want your main drive and SSDs in those slots. Answer 1 of 7.
It really doesnt matter to be honest. When you boot your computer the BIOS will look at the disk connected to SATA port 0 first then SATA port 2 etc. However the real story here is a comparison to even the slowest SSD Intels SSD 320 and Western Digitals.
For ease of use I would connect SSD to SATA6G-1 because BIOS looks for first port first. While the official SATA-IO documentation states that there is no difference between SATA 3Gbs and SATA 6Gbs cables there were still some people that insisted that you needed a SATA. So what you have planed will be fine as long as the ssd is in.
Otherwise it wont matter. Regardless of which CPU or chipset we used almost all the SATA 6Gbps ports proved faster than the SATA 3Gbps ports in every test. Only thing I know for sure about that mobo.
It really doesnt matter. Before running the speed tests we cut open a set of cables to see if we could. When SATA 6Gbs drives were first launched there was a lot of confusion over whether or not you needed a special cable in order to get the full speed benefit of SATA 6Gbs.
SATAExpress is a very fast SATA standard but I highly doubt you have hardware compatible with it. Its essentially been replaced by M2. Instructions for how to use Windows Device Manager to determine if you have one of the impacted Intel 6 Series chipsets in your system can also be found in the.
Typically the first set of ports are on on the Intel controller which unless you want RAID will be fine. What does that mean for other Thunderbolt products that only use one PCIe lane. But if you want to go in sequential order SATA ports should be listed on the MB from 1 to whatever many ports there are so I guess set your system HD to the first one and the rest use them in whichever order.
Probably does not matter Id put it into SATA6G_3 as SATA6G_5 and SATA6G_6 MAY be using different controller. The red ones are Jmcron they are not as good performance wise or user freindly wise I use them but only for CDDVD drives for 1 X25 use port 0 it will be the port closet to the board and the two red ports It will not matter if your just running the drive but will matter if you use the Firmware update program. Some start numbering with 0 others with 1 but it doesnt matter as BIOS could be set to BOOT first from any port.
And thus if you dont have any m2 drives it doesnt matter at all. Afterall moving to an authentic SATA 6Gbs cable cleared up our problems the first time right. We prefer to have empirical data to back up these types of claims however so we decided to compare a set of supposed SATA 3Gbs cables against a SATA 6Gbs cable.
At the time the magic of an SSD wasnt necessarily that it could shoot dizzying amounts of data.
Does It Matter Which Sata Port You Use Pc Guide 101
Does It Matter Which Sata Port You Use Pc Guide 101
Does It Matter Which Sata Port You Use Pc Guide 101
0 Response to "Does It Matter Which Sata6g Port Is Used First"
Post a Comment